TABLE OF CONTENTS
Estimated reading time: 4 minutes, 20 seconds
The indicator LED on your bluebot is located next to your power button. During setup you will be prompted to pay attention to the color of the device indicator LED as you connect and install your device. If a problem occurs you may also use the status of the device to troubleshoot and potentially come to a resolution.
If you are experiencing an issue you can use the behavior patterns below to locate your issue and find the solution.
Yellow lights are all about connection, you will see a yellow light when connecting your bluebot to your home network before it eventually turns blue and connects to the cloud or fails and shows a different behavior pattern.
Blinking Yellow: attempting to connect to the last known Wi-Fi network SSID (Network Name) and Password that was input by the user via the bluebot app.
Weak Wi-Fi Signal Strength At Install Location
Attempting to connect to the access point, connection successful, repeat.
Solution: You may need to install a quality Wi-Fi repeater to increase the strength at the install location, especially if you're in a basement or detached garage or attempting to install the bluebot on your well head etc. Read more here about Wi-Fi Troubleshooting.
Tip: It can be helpful if you have a mesh system with an app to create a dedicated network for your iOT devices like bluebot.
Incorrect Credentials or Too Far From The Access Point
Attempting to connect to the access point, connection failed.
Solution: Ensure your network name (SSID) and password are correct, this is a very common issue. You may also be too far from your router, to test plug the bluebot device in near your router to rule out a wrong password. Read more about Wi-Fi Troubleshooting.
RF (radio frequency) Interference can interfere with the required 2.4ghz channel that the bluebot uses to connect and transmit data to the cloud. Microwave ovens, cordless phone systems, bluetooth systems and other Wi-Fi networks can all be responsible.
Cycling between flashing and solid green (without button input indicates environmental interference.
Solution: Troubleshooting RF / Wi-fi Interference can be done by using a tool like NetSpot to reduce interference by identifying what is causing the issue in the first place. You may also attempt to connect the bluebot to the network outside of the home or area of interference and then take it to the install location and see if it will maintain a connection.
False Flow - Signal Noise
If the LED is blinking when you know there is no flow, this may be a "False Flow" caused by signal noise. Noise in rare cases is an installation issue found with all ultrasonic flow meters. If you see in your app show 0.1 to 0.4gpm flowing consistently it could be considered "noise" or false flow. Your bluebot can re-zero itself using the App--this function can be found in the Hardware Section by selecting "Device Profile" then scrolling down and selecting "Sensor Details".
LED Behavior pattern: Flashing one time very regularly (every 30 seconds or every minute)
|Flashing||Solid||repeats every 30 - 60 seconds|
Tip: Your bluebot flashes to indicate the flow rate, if your bluebot is flashing blue at different speeds and even flashing very slowly, this can be used as a manual indicator of water flowing. If you know NO water is flowing and the light is flashing you may need to Set the Zero Point for the device in the "Sensor Details" section found in the "Device Profile" section
This is generally a firewall setting on your Wi-Fi network and is most common in commercial network environments.
Flashing one time very regularly (every 30 seconds or every minute)
Solution: We recommend consulting your IT/ISP professional and/or contacting us.
This is generally a firewall setting on your Wi-Fi network and most common in commercial network environments.
Solution: Restart the connection process if you're experiencing this during initial setup of the device. If the LED indicator is red after you have had the device operational make sure the Wi-Fi network is working properly and that the password has not been changed. In rare cases where customers have accidentally dropped the bluebot or it has been improperly installed the red status can indicate total failure which would require a replacement of the device itself.
Poor Ultrasonic Signal Quality
Possible cause: device adjustment, empty pipe during last rescan, dirt/debris interfering with device ultrasonic sensors.
Solution: Perform a rescan when you are sure your pipe is pressurized/full. If that does not resolve your issue, check on your device installation status. Remove from the pipe, check the ultrasonic pads for dirt/debris, and ensure the bluebot is placed with a tight snug fit on the centerline of pipe as shown in the illustration.
Read all about signal quality HERE
If you have any questions or would like to speak to a member of the bluebot team, contact us directly at firstname.lastname@example.org or call/text (831) 275-2715 M-F 10 AM - 6 PM PST.